Custom made high arch soles are usually made for the the people who have severe cases of low foot arches or complete flat feet. Of course the custom made ones are made from the manufacturers have the specific measurements and such that the flat footed patient will need but what many do not know is that it is possible to create handmade orthotics. The only catch here is that only athletes or people with a mild case of low arch may be able to use it just to be safe.
Now if one would want to make a homemade arch support insole, then he would have to buy a few things. Firstly, he will be needing two to three old insoles that would probably come from an old pair of shoes. He has to make sure that the insoles all have the same size.
Once these soles have already been gotten, then the very next thing to do would be to get some glue. One is recommended to use super glue for this kind of project because super glue is very efficient and dries fast. However, if one does not have super glue in his house, then he may use some other sticky glue that is waterproof.
So after getting the old insoles, one has to now do a bit of measurements. Always do make sure that all insoles have the same size so that it will be easier to place them on each other. So when one puts one insole on top of the other, he has to find the part that holds the arch of the foot.
After determining the part that would hold the arch, then he now has to cut that part with the sharp scissors. Now he has to make sure that the part that was cut out is really able to fit the insole that is whole otherwise one would have to cut it a little bit more. Once he has already done that, then the next part would be to now glue that small part to the whole insole.
Now when that is already done, then all that is left to do is wait for the glue to dry. If the glue takes a bit long to dry, then he may put the sole in front of an electric fan so that it will dry faster. However, if one uses super glue, then the glue will be able to dry in just a few minutes.
Now if one would want to make his arch support taller than it already is, he can actually do so by adding another sole part to the insole. Now he has to get the third insole and just what he did a while ago. Once he has done that, he just once again has to let the glue dry and then try to walk with it.
Now making handmade orthotics at home as quite easy as one will be able to see. However, do not try to do this if the flat feet case is quite severe. These handmade ones should only be used for those whose cases are not severe as the severe cases would already need the custom made ones with specific measurements.
Now if one would want to make a homemade arch support insole, then he would have to buy a few things. Firstly, he will be needing two to three old insoles that would probably come from an old pair of shoes. He has to make sure that the insoles all have the same size.
Once these soles have already been gotten, then the very next thing to do would be to get some glue. One is recommended to use super glue for this kind of project because super glue is very efficient and dries fast. However, if one does not have super glue in his house, then he may use some other sticky glue that is waterproof.
So after getting the old insoles, one has to now do a bit of measurements. Always do make sure that all insoles have the same size so that it will be easier to place them on each other. So when one puts one insole on top of the other, he has to find the part that holds the arch of the foot.
After determining the part that would hold the arch, then he now has to cut that part with the sharp scissors. Now he has to make sure that the part that was cut out is really able to fit the insole that is whole otherwise one would have to cut it a little bit more. Once he has already done that, then the next part would be to now glue that small part to the whole insole.
Now when that is already done, then all that is left to do is wait for the glue to dry. If the glue takes a bit long to dry, then he may put the sole in front of an electric fan so that it will dry faster. However, if one uses super glue, then the glue will be able to dry in just a few minutes.
Now if one would want to make his arch support taller than it already is, he can actually do so by adding another sole part to the insole. Now he has to get the third insole and just what he did a while ago. Once he has done that, he just once again has to let the glue dry and then try to walk with it.
Now making handmade orthotics at home as quite easy as one will be able to see. However, do not try to do this if the flat feet case is quite severe. These handmade ones should only be used for those whose cases are not severe as the severe cases would already need the custom made ones with specific measurements.
About the Author:
For a summary of the advantages of handmade orthotics don't hesitate to check out our website today. To reach our homepage now, just click on this link http://www.customorthoticfootbeds.com.
No comments:
Post a Comment